Maintenance Technician II
Cambro Manufacturing Company is hiring for Maintenance Technician II in Mebane, NC. Mid level. First seen November 13, 2026; open as of November 19, 2026. Jobs taken straight from company career pages — no aggregator in between.
Save to applyFree forever. No commitment, no card required.
- Company
- Cambro Manufacturing Company
- Where
- Mebane, NC
- Level
- Mid
- First seen
- November 13, 2026
- Listed via
- Workday
- Open for
- 6 days, as of November 19, 2026
Applying to this one?
See how well you fit, before you apply
Save it to your board. Add your résumé once, and Destava shows where you are strong, what is missing and how to pitch yourself, then tailors your résumé to this posting.
- Found it
- Save it
- See your fit
Free forever. No commitment, no card required.
About this job
This role keeps all factory machinery running through scheduled upkeep, emergency fixes, and new equipment setup. You will report to the Senior Maintenance Tech Supervisor at the temperature-controlled Mebane, NC plant. The position is on third shift and may require overtime.
Schedule: Third shift, with overtime as needed and possible schedule changes.
Responsibilities
- Take apart, clean, swap out, and fix broken machines or their electrical, electronic, mechanical, hydraulic, and pneumatic parts by hand.
- Find what is wrong by watching machines closely and using test tools and knowledge of how they work.
- Do scheduled preventive upkeep on time according to the set intervals.
- Lay out, put together, install, and maintain piping systems and related hydraulic and pneumatic gear.
- Install, program, or repair automated equipment like robots and programmable controllers.
- Set up and run lathes, drill presses, grinders, and other metalworking tools to make and fix parts.
- Check and measure parts for wear, misalignment, or other issues.
- Use cutting torches or welding gear to cut or join metal parts.
- Look at, touch, and listen to machines to find what is causing breakdowns.
- Read blueprints, ladder logic, and electrical, hydraulic, and pneumatic diagrams to troubleshoot machines.
- Use forklifts, hoists, chains, straps, or slings to lift, move, or position equipment.
- Keep tools, parts, materials, and the work area clean and well cared for.
- Act as a contact with vendors when needed.
- Show up reliably and on time, and be dependable to meet department and company needs.
- Carry out every essential duty satisfactorily to do the job well.
- Follow all safety rules, wear required PPE, attend safety meetings, and report unsafe equipment or conditions.
- Work well as a team member, give and take feedback, and treat everyone with respect.
- Take ownership of your work and behavior, accept accountability, encourage solutions, and update others on project status.
- Follow all department quality standards and raise concerns to your manager.
- Understand and show Cambro's culture and core values of Safety, Quality, Respect, and Service.
- Know the department's key performance indicators and help reach those goals alone and with the team.
- Do other tasks as assigned.
- Connect to PLCs to help fix logic or control problems, monitor and change ladder programs, and transfer files between a PC or laptop and the PLC.
- Check that machines or robots are set up correctly and run them by hand to confirm what is wrong or that repairs worked.
- Experienced Tech II's should mentor new employees and teach them policies, procedures, and repair methods.
- Spot and report possible equipment failure or unsafe conditions to the Sr Maintenance Tech Supervisor.
- Log all repairs and resolutions in a CMMS database.
- Help write and update preventive and corrective procedures and checklists for all production equipment.
- Keep improving your technical skills through workshops, classes, or online training.
- Work overtime as needed and stay flexible for possible schedule changes to meet business needs.
Requirements
- Have a two-year or four-year certificate from a college or technical school, or five to ten years of related experience in an industrial manufacturing setting, or an equivalent mix of education and experience.
- Have two to five years of preventive or corrective maintenance experience in at least one of these manufacturing processes: Injection Molding, Compression Molding, Composite Molding, or Roto Mold.
- Read and understand documents like mechanical, electrical, and hydraulic prints or schematics, safety rules, operating and maintenance instructions, and procedure manuals.
- Write routine reports and correspondence, and speak effectively to groups of customers or employees.
- Work with math concepts like probability, statistical inference, and basics of plane and solid geometry and trigonometry.
- Apply fractions, percentages, ratios, and proportions to real situations.
- Solve practical problems and handle various concrete variables where only limited standardization exists.
- Interpret instructions given in written, oral, diagram, or schedule form.
- Use a respirator if needed, as the role may involve particulate levels at or above the OSHA permissible exposure limit.
- Handle physical demands including sitting, walking, standing, bending at the neck and waist, squatting, climbing, kneeling, crawling, twisting at the neck and waist, repetitive hand use, simple grasping, power grasping, fine manipulation, pushing and pulling, reaching above and below the shoulder, a
- Drive cars, trucks, forklifts, and other equipment.
- Work around equipment and machinery.
- Handle exposure to excessive noise.
- Handle exposure to dust, gas, fumes, or chemicals.
- Work at heights.
- Use special visual or auditory protective equipment.
- Walk on uneven ground.
- Operate foot controls or do repetitive foot movement.
- Handle risk of exposure to bio-hazards like bloodborne pathogens, sewage, and hospital waste.
- Wear required PPE: safety glasses, utility gloves, steel-toe slip-resistant shoes, hardhat, hearing protection, face shields, and a face covering per company policy.
- Be authorized to work for any employer in the U.S. (no visa sponsorship available).
Nice to have
- Previous experience in corrective or preventive maintenance and troubleshooting with Haitian 2 and 3 platen injection molding machines, JSW hydraulic or electric injection molding machines, Husky Hydraulic injection molding machines, Blow molding machines, and Uniloy Structural Web molding machines.
- Experience with Star & Yushin Robots.
- Experience with Ferry Rotational molding machines.
- Experience with Compression press molding machines.
- Experience with Martin Pultrusion molding machines.
- Experience with Conair & Universal Dynamics (Una-Dyn) material handling equipment and Matsui Dryer material handling equipment.
- Previous training or certification in operating forklifts, scissor lifts, and boom lifts.
Read more and apply on Cambro Manufacturing Company's site
Questions about this job
When was this Maintenance Technician II job at Cambro Manufacturing Company posted?
November 13, 2026
Destava first saw it on November 13, 2026, on Cambro Manufacturing Company's own careers page (Workday).
Is Cambro Manufacturing Company still accepting applications for it?
Open as of November 19, 2026
It was open on Cambro Manufacturing Company's own site when Destava last read it, on November 19, 2026, 6 days after we first saw it. When the company takes it down, this page says the job has closed.
How do I apply for Maintenance Technician II at Cambro Manufacturing Company?
On Cambro Manufacturing Company's own site
On Cambro Manufacturing Company's own site, at cambro.wd5.myworkdayjobs.com: open the posting. Destava does not take the application. Save the job to your Destava board to track it, see how well you fit and tailor your résumé to it.
Is this Cambro Manufacturing Company job posting legit?
Listed on Cambro Manufacturing Company's own careers page
Destava read it on Cambro Manufacturing Company's own careers page at cambro.wd5.myworkdayjobs.com, run on Workday, not on a job board. First seen November 13, 2026. Apply on the company's own site, and never pay to apply for a job.
How many maintenance and repair workers, general jobs are open in Raleigh–Durham?
247 open
247 open, 104 of them new this week, at 129 companies: see them all.
More jobs like this
Maintenance Technician III - Asheboro
Save to applyMaintenance Technician II - Reedy Fork
Save to applyMaintenance Technician III - Reedy Fork
Save to applyMaintenance Technician, Multifamily
Save to apply
See all 247 Maintenance and Repair Workers, General jobs in Raleigh–Durham
A search agent finds the jobs this list misses: the ones that mean the same without the same words. Have Destava watch for maintenance technician ii jobs in Mebane, NC, new matches every morning on your own account.
With Destava: Save to apply · Tailor my résumé · Write a cover letter
This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.