Maintenance Technician II
Cambro Manufacturing Company is hiring for Maintenance Technician II in Huntington Beach, CA. Mid level, $30–$36 an hour stated. First seen November 13, 2026; open as of November 19, 2026. Jobs taken straight from company career pages — no aggregator in between.
Save to applyFree forever. No commitment, no card required.
- Company
- Cambro Manufacturing Company
- Where
- Huntington Beach, CA
- Level
- Mid
- Pay stated
- $30–$36 an hour
- First seen
- November 13, 2026
- Listed via
- Workday
- Open for
- 6 days, as of November 19, 2026
Applying to this one?
See how well you fit, before you apply
Save it to your board. Add your résumé once, and Destava shows where you are strong, what is missing and how to pitch yourself, then tailors your résumé to this posting.
- Found it
- Save it
- See your fit
Free forever. No commitment, no card required.
About this job
This is a Maintenance Technician II role at Cambro Manufacturing Company in Huntington Beach, CA, reporting to the Maintenance Senior Tech Supervisor. The job involves performing preventive and corrective maintenance on manufacturing machines and support equipment to meet production and quality goals. The position is first shift and requires overtime as needed.
Schedule: First shift, with overtime as needed and possible schedule changes
Responsibilities
- Clean, take apart, replace, and fix broken machines or their electrical, electronic, mechanical, hydraulic, or pneumatic parts as directed
- Check and service lubrication systems, keeping grease and oil at proper levels
- Carry out preventive maintenance on production machines and support equipment
- Inspect and measure parts to spot wear, misalignment, or other issues
- Look at, touch, and listen to machines to find what is causing problems
- Enter codes or other data into computers
- Read blueprints, ladder logic, and electrical, hydraulic, and pneumatic schematics to troubleshoot machines with higher-level technicians
- Act as a contact with vendors when needed
- Keep reliable and consistent attendance, being punctual and dependable
- Perform each essential duty satisfactorily to succeed in the job
- Follow all safety procedures, wear PPE as needed, attend safety meetings, and report safety issues or hazards
- Work well as a team member, give and receive feedback, and treat everyone with respect
- Take ownership of your work and behavior, accept accountability, encourage solutions, and communicate work status
- Follow all department quality standards and raise concerns to your manager
- Understand and show Cambro's culture and core values (Safety, Quality, Respect, Service)
- Know the department's key performance indicators and help reach them individually and as a team
- Do other duties as needed
- Help higher-level technicians install new equipment
- Use printed or electronic documents like manuals, cut sheets, or manufacturer websites to learn about maintenance procedures, frequencies, or materials
- Work with higher-level technicians to learn more about equipment operations, maintenance procedures, and troubleshooting
- Work overtime as needed and stay flexible for possible schedule changes
Requirements
- High school diploma or GED
- At least one year of related experience or training, or an equivalent combination of education and experience in industrial mechanical maintenance
- Ability to write routine reports and correspondence
- Ability to speak effectively before groups of customers or employees
- Ability to communicate effectively, both orally and in writing
- Ability to work with math concepts like probability, statistical inference, plane and solid geometry, and trigonometry
- Ability to apply fractions, percentages, ratios, and proportions to practical situations
- Ability to solve practical problems with limited standardization
- Ability to interpret instructions in written, oral, diagram, or schedule form
- Ability to use a respirator if needed due to possible particulate exposure at or above OSHA limits
- Physical ability to sit, walk, stand, bend at neck and waist, squat, climb, kneel, crawl, twist at neck and waist, use hands repetitively, grasp, manipulate finely, push and pull, reach above and below shoulder, and carry or lift up to 50 lbs
- Ability to drive cars, trucks, forklifts, and other equipment
- Ability to work around equipment and machinery
- Ability to tolerate excessive noise
- Ability to tolerate dust, gas, fumes, or chemicals
- Ability to work at heights
- Ability to use special visual or auditory protective equipment
- Ability to walk on uneven ground
- Ability to operate foot controls or use repetitive foot movement
- Ability to handle risk of exposure to bio-hazards like bloodborne pathogens, sewage, or hospital waste
- Must wear safety glasses, utility gloves, steel-toe slip-resistant shoes, hardhat, hearing protection, face shields, and face covering per company policy
- Must be authorized to work for any employer in the U.S. (no visa sponsorship)
Nice to have
- Ability to read and interpret mechanical, electrical, and hydraulic prints or schematics, safety rules, operating and maintenance instructions, and procedure manuals
- At least one year of maintenance experience in injection molding, compression molding, composite molding, or roto mold manufacturing
- Basic to intermediate electrical training or experience with single and three phase circuits up to 480 volts
- Computer proficiency in Microsoft Excel, Word, job-related internet research, and ability to learn the CMMS
- Functional knowledge of mechanical components like valves, pipe fittings, bearings, motors, and gearboxes
- Trade or vocational school degree
- Training or certification in operating electric or propane forklift, scissor lift, or boom lift
Read more and apply on Cambro Manufacturing Company's site
Questions about this job
When was this Maintenance Technician II job at Cambro Manufacturing Company posted?
November 13, 2026
Destava first saw it on November 13, 2026, on Cambro Manufacturing Company's own careers page (Workday).
Is Cambro Manufacturing Company still accepting applications for it?
Open as of November 19, 2026
It was open on Cambro Manufacturing Company's own site when Destava last read it, on November 19, 2026, 6 days after we first saw it. When the company takes it down, this page says the job has closed.
How do I apply for Maintenance Technician II at Cambro Manufacturing Company?
On Cambro Manufacturing Company's own site
On Cambro Manufacturing Company's own site, at cambro.wd5.myworkdayjobs.com: open the posting. Destava does not take the application. Save the job to your Destava board to track it, see how well you fit and tailor your résumé to it.
Is this Cambro Manufacturing Company job posting legit?
Listed on Cambro Manufacturing Company's own careers page
Destava read it on Cambro Manufacturing Company's own careers page at cambro.wd5.myworkdayjobs.com, run on Workday, not on a job board. First seen November 13, 2026. Apply on the company's own site, and never pay to apply for a job.
What does this job pay?
$30–$36 an hour
The posting states $30–$36 an hour.
How many maintenance and repair workers, general jobs are open in Los Angeles?
536 open
536 open, 184 of them new this week, at 252 companies: see them all.
More jobs like this
Field Service Technician
Save to applyMechanical Repair Technician I (Onsite)
Save to applySenior Maintenance Technician
Save to applyMaintenance Engineer
Save to apply
See all 536 Maintenance and Repair Workers, General jobs in Los Angeles
A search agent finds the jobs this list misses: the ones that mean the same without the same words. Have Destava watch for maintenance technician ii jobs in Huntington Beach, CA, new matches every morning on your own account.
With Destava: Save to apply · Tailor my résumé · Write a cover letter
This page includes information from the O*NET 31.0 Database by the U.S. Department of Labor, Employment and Training Administration (USDOL/ETA). Used under the CC BY 4.0 license. O*NET® is a trademark of USDOL/ETA.